Bluelab MONGUA Guardian Monitor for pH, Temperature, and Conductivity Measures, Easy Calibration and Wall Mounted

Product Information

Your settings are saved if power is lost. Better yert, no calibration's needed for your CF or temperature. To calibrate your pH, there's one simple button.

In just one glance the Guardian Monitor measures all three critical parameters to successful growth; pH, conductivity and temperature. Seasonal changes, sunlight hours, wind, inherent plant growth; from vegetative to fruiting; are all influencing factors to plant growth success. More importantly...these parameters change the plants uptake and need of water and specific nutrient elements. The Bluelab Guardian is a constant indicator of the desired levels of EC, pHand temperature, enabling the grower to optimise these parameters as the crop progresses through each growing phase. The Bluelab Guardian Monitor Wi-Fi is not only a constant indicator of the desired levels of pH, conductivity and temperature of your nutrient solution, it is also compatible with Edenic by Bluelab software. So confident are Bluelab in this product's robustness, that every Guardian comes supplied with a two year guarantee. Only the pH probe is exempt, due to the delicate nature of its glass parts, yet even this still comes with a guarantee of 6 months.In just one glance the Bluelab Guardian Monitor measures all three critical parameters pH, conductivity and temperature. Yes, both the Bluelab Conductivity/Temperature Probe and the Bluelab pH Probe are fully submersible. Is the Bluelab pH Probe replaceable? The alarm function will warn you with a flashing LED when readings drop below, or rise above, a pre-determined value. To set the alarm hold the alarm button until the letters 'AL H' are displayed in each of the three display windows. As soon as you take your finger off the button, the current highest values will be displayed in the three windows. Use the unit buttons to select which parameter you wish to adjust and then use the up and down buttons to lower or increase the each maximum parameter value. Remember that you are setting the highest acceptable value. If levels go above this, then the visual alarm will start to flash. Once you've set the high values, press the alarm button to move onto the low values and repeat the process. Press the alarm button again and your chosen parameters will be saved. The Bluelab Guardian monitors temperature in centigrade or Fahrenheit, conductivity in terms of EC / CF / TDS / ppm, and also pH levels – and it does it consistently and accurately, with the use of scientific grade external probes. The Guardian will even provide a visual alert should levels drop below, or rise above, pre-programmed values – minor issues can then be dealt with before they become major issues.

pH Probe calibration must be done before use. EC probe does not require calibration but both probes need to be in the solution for pH to compensate for temperature. Fit the (optional) pH probe holder to the stem of the pH probe. Do not flex or bend the probe stem as it may break! Bluelab pH Probes: Care, maintenance and storage- Clean, hydrate and calibrate your pH probe monthly. Read more on provisioning here. Why does the Bluelab Guardian reading start at 5 EC then drop down to the correct reading when you initially power it up? Bluelab pH Probes: Care, maintenance and storage - Clean, hydrate and calibrate your pH probe monthly. Step 6: Placement of probesTo select your desired conductivity unit, hold the unit button, located next to the conductivity display, down for 3 seconds. This process will trigger a move to the next unit of measurement, as indicated by the 3 LEDs to the right of the display. Repeat this process until you have arrived at your chosen unit of measurement. Repeat the whole process again for your choice of temperature measurement.

Yes. A Bluelab Wi-Fi device can be reprovisioned onto a new Wi-Fi Network by entering “Provisioning Mode” on the device and using the Edenic phone app to configure the device. Monitor your nutrient pH, CF & temperature 24 hours a day with Bluelab Guardian. All readings are live! The Bluelab Guardian can be mounted in a suitable area, using the 4 supplied screws. Make sure that it is placed in an area that will allow the probes to reach the reservoir tank comfortably – no further than two meters away. Two cable ties are supplied with the unit, which can be used to mount it to a support or hanging bar. Avoid positioning the Guardian in areas of direct sunlight. Though the unit is water resistant, you should also avoid positioning it in areas where it can easily be splashed with nutrients. Mineral salt deposits can be corrosive and cause damage over long periods of time.With Edenic, manage your Guardian Monitor Wi-Fi from where you like, when you like. Control parameters, monitor your environment and learn from your data with custom reporting. Visit: www.edenic.io Probe maintenance: Long-term, the two pH LEDs located to the right of the pH read-out display will keep you informed of the pH calibration status. Consult the full instruction manual for full details on the different statuses. Effectively, if both LEDs are not lit permanently then calibration of some form is required. The Bluelab Guardian Monitor is mains-powered and is mounted to the wall or hung on a support and the probes simply placed into the pond water, filter. Many plants flower as a result of changes in the number of hours of uninterrupted darkness they're exposed to. The display LEDs on the Guardian glow in a plant-safe green that won't disturb dark periods and cause unwanted issues.