youyeetoo NanoPi R5S Mini Router with Metal Case,4GB LPDDR4 16GB EMMC, RK3568 Development Board 0.8TOPS NPU Support Docker Three Ethernet Ports USB3.0 HDMI Support M.2 NVMe PD Power (Power Bundle)

Product Information

For more details please refer to the document： NanoPi-1507-Dimesions(dxf).zip 4 Get Started 4.1 Essentials You Need All in all, the NanoPi R5S is a board featured with multiple Ethernet ports, light NAS and video playing. It is a cannot-miss platform with infinite possibilities for geeks, fans and developers. Connect your development board to your computer using a USB A-to-A data cable, referring to the figure below, be sure to connect it to the USB port closest to the edge: Enter the "Services" -> "Terminal", enter the "poweroff" command and hit enter, wait until the led light is off, and then unplug the power supply. You need to add an LCD variable in U-boot. For example if you want to connect your NanoPi to an S70 LCD you can do it this way:

A little further down in the FriendlyElec wiki post ( here), after the image is installed to the eMMC, there is a firmware bundle that gets flashed to the drive as well. Is this firmware bundle included in the DietPi image, or otherwise not needed if using DietPi? The NanoPi can work with FriendlyARM's LCDs: H43,S70,A70,W50,A97,L80,G10,A56,W101,W35,P43,P35,TD35. This option is ideal if you want to build a NAS Server and connect a few external Hard drives. Just keep in mind that it is most likely that the metal case lower cover might not close correctly if you plan to add this expansion card.

Contents

No bloatware or spyware. Special utilities are completely optional. Suitable for newcomers and professionals. Optimized

FriendlyWrt is a customized system made by FriendlyElec based on an OpenWrt distribution. It is open source and well suitable for developing IoT applications, NAS applications etc. opt/toolchains/gcc-arm-8.3-2019.03-x86_64-aarch64-linux-gnu/bin/aarch64-linux-gnu-gcc -std =c99 -Wall -Wextra -pedantic -MMD -ggdb -c -o f3read.o f3read.c Ubuntu 20.04 Desktop, LXQT desktop, pre-installed mpv, smplayer and chromium brower, supports hardware acceleration There are also 2x USB 3.0 ports, an SD card holder and between the SD card the USB there’s an expansion connector for UART/SPI/PWM. The debug uart (console) is next to the LAN2 2.5G port. This is useful to solder a pinheader and connect a USB-to-UART module to get the output for debugging.

Other supported variants

I was especially very pleasantly surprised to see that the brd module is not compiled inside the kernel, but as a module.

You were playing with FriendlyWrt, a customized version of OpenWrt developed by the FriendlyElec team. According to system information, only 9% of 2GB RAM is utilized, maintaining low system resources in Idle operation mode. Also, using the maximum bandwidth provided by your ISP is achievable and highly recommended by connecting the board to 2.5G LAN or WAN ports in your router. eth0: mtu 1500 qdisc mq state DOWN mode DEFAULT group default qlen 1000 COLLECT_LTO_WRAPPER= /opt /FriendlyARM /toolchain / 11.3-aarch64 /libexec /gcc /aarch64-cortexa53-linux-gnu /11.3.0 /lto-wrapperThe NanoPi R5S Case has a built-in cork you can pull out. Most likely designed for future board design with built-in WiFi support included. It’s possible to pull it out and install an external Antenna w/ an SMA Male Connector plug. After installing the adapter, you can install a WiFi 6 PCIe Card.