15mm White SPEEDFIT Collet Locking Clip - CM1815W - Pack of 10

Product Information

For general guidance on pipework sizing, please refer to BS6700 and BS5449 or the Institute of Plumbing Engineering Services Design Guide. Speedfit fittings are suitable for connection to pipe sizes within ±0.1mm of nominal size. Remember that pressure testing is NOT a substitute for making sure fittings are clean and free of any grit, dirt or swarf and the pipe is correctly inserted (see “How to Make a Connection”). System Commissioning and Flushing Pipe clips should not be fitted any closer than 60mm from the end of the fitting to allow for expansion. Pipes should always be adequately supported to prevent undue stress or side load on the fittings. Recommended Clip spacing Pipe Diameter The push-fit solutions can also be found in water purification systems. These food grade fittings have been designed specifically for fluid control and drinks dispensers meaning that when using water systems in offices and other public places, water is safe to drink, while systems are easy to maintain and repair.

We take pride in the quality of our products and all complaints are investigated thoroughly. If you have a problem with a Speedfit Product please return both fitting and pipe to us for investigation. We will need at least 50mm of pipe to ensure an accurate analysis. If there is a suspicion that the pipe is faulty, please provide marking details from the pipe. Common Problems and Identification No taste, colour, odour or toxicity is imparted to water by Speedfit components, nor do they promote microbiological growth. Speedfit pipework can be easily cabled through studwork and within wall systems as well as behind “dot and dab” plasterboard installations. Speedfit 10mm B-PEX Barrier pipe is most commonly used to feed radiators. If incorporating fittings in this way, collet covers or collet clips must be used within the Standard (PKM) range of fittings. Wet plaster The stem of the insert gives greater rigidity of the length of pipe within the fitting, reducing the chance of leaks if a side load is applied.

Details

To prevent surface damage to the plaster caused by expansion and contraction of Speedfit pipes, it is important to ensure that all Speedfit pipework is channelled into the wall and protected with appropriate sleeving. Alternatively, the pipework can be surface mounted and boxed in if required for aesthetic appearance. Whether you are working on a new build or a repair and maintenance job, Speedfit fittings come in a wide range of sizes to suit any domestic or light commercial application. Speedfit’s extensive choice of plastic, brass and chrome fittings, tap connectors, valves, and Flexi hoses gives you everything you need to complete the job in no time. By combining these products with plastic push-fit pipe, you can create truly flexible and affordable plumbing and heating system.

Sealed central heating systems provided temperatures and pressures comply with BS7291 Parts 1 and 3 Class S With existing systems, flushing prior to the use of Speedfit is essential to remove any harmful contamination or chemical residues from elsewhere in the system. Holes may be located vertically anywhere in the web, but leave 3mm web at the top and/or bottom of hole. Do not cut into joist flanges when cutting the web. Speedfit is well suited for steel frame construction and care should be taken when installing the pipework. This will also eliminate the risk of damage by floorboard nails. There is no need for dry runs since pipe can be cut and connections made in-situ.It is also possible to bend Speedit Pipe using a standard pipe bender. The pipe should not be heated with a blowlamp or hot air gun. They are made using precision engineering, extensive research, and rigorous testing, Speedfit products blend push-fit and multi-seal technology for a reliable leak-proof connection. Simple to install and using fewer links than traditional methods, Speedfit cuts installation time by 40% so that you can say goodbye to time-consuming and costly plumbing jobs. Plus, no tools are required when installing or demounting fittings, making it easy to maneuver in tight spaces or readjust joins. Speedfit Conduit Pipe is supplied in either 15mm or 22mm (internal diameter) sizes. The flexible convoluted pipe has an outside diameter of 24mm and 30mm. Coils of either 25m or 50m length are available. Exposed pipework

Ensure the pipe is free of score marks. Cut the pipe square. When using Speedfit Barrier Pipe cut along an insertion mark. We recommend the use of JG Pipe Cutters. To prevent damage to the ‘O’ ring remove all burrs and sharp edges.Speedfit can be disinfected with chlorine (sodium hypochlorite) after installation. Domestic systems are disinfected with a solution of chlorine with a concentration of 50ppm (mg/l) for one hour. The concentration should not be less that 30ppm at all draw off points after this time.