With a multi-functional LCD digital display and array of exclusive features such as Alarm Memory, Ventilate Instruction, Quiet Self Test and Environmental Sensing, the FA3322X4 offers the highest level of CO detection for your home. Battery powered carbon monoxide alarms can typically be installed wall-mounted or left free-standing on flat, level surface. Also note that carbon monoxide has been proven to spread into neighbouring properties through open windows and, in semi-detached or terrace houses, through loft spaces. If your property has an attached garage with a connecting door through to the house, it is recommended to fit a CO alarm inside the house leading from that doorway. Do not install CO alarms within 3 metres of doors or windows, above radiators, or immediately close to anything that gives off steam or fumes like a cooker or shower room. Similarly, it is not recommended to install detectors in dusty areas such as workshops or garages.

CO detectors should be installed near potential sources of carbon monoxide, essentially any fuel-burning appliances such as boilers, cookers and ovens, fireplaces (both open and enclosed burners), and portable generators. As you are likely to be most affected by CO in areas of your home that you spend the most time in it is advisable to install alarms in those areas as well, such as the living room and bedrooms. It is also worth noting that while one detector is better than no detectors at all, larger homes may require several detectors to cover the property fully. CE marked and Kitemarked to BS EN 50291-1 (domestic use) & BS EN 50291-2:2010 (camping/caravans/boats) To activate your CO alarm, pull the disabling tab out of the alarm and wait up to 1 minute for the green LED to flash to confirm the alarm is active. After 1 minute, press the test button to hear the alarm sound. Please note, the alarm will not sound before the 1 minute activation period is complete. CO alarms and rental propertiesWith low level CO monitoring, a pre-alarm warning to open windows helps reduce the risk of CO poisoning and prevents build-up of dangerous CO levels. If a room is not ventilated and ppm levels continue to increase, the alarm will activate. Near an appliance: they should be placed within 1 to 3 metres horizontally from the appliance and between the height of the appliance to 150mm below the ceiling – i.e., not above a stove where it would be in the path of steam or fumes. In living spaces: they should be positioned close to where the occupant's head is likely to be most of the time – e.g., on your bedside table. Carbon monoxide is a highly poisonous gas, caused by fuel not burning properly. It cannot be seen, smelt or tasted by the human senses and is only detectable through a CO alarm. If your FireAngel carbon monoxide alarm is new and the test button is not working, try removing the isolation pin. Once removed, wait for at least 1 minute for alarm to initiate. If the alarm now sounds once test button is pressed your alarm is working correctly. If it still does not sound, please get in touch with our Customer Support team.

All alarms are calibrated and rigorously tested in-house and are third party tested to receive the BSI Kitemark certification to provide peace of mind. Also, the new range is compliant with the revised European Standard EN 50291-1:2018 to ensure maximum protection. FA3322X4: Carbon Monoxide Alarm with digital display and 10 year battery Find out more about the FA3313X4 CO Alarm. FA6813-EU: Carbon Monoxide Alarm with replaceable batteries If you have had your FireAngel carbon monoxide alarm for a few years but it is still within warranty, and the isolation pin has been removed, please get in touch with our Customer Support team. If it is not within warranty, please replace your alarm as soon as possible. Why is my FireAngel CO alarm beeping?An audible Carbon Monoxide detector is the only way to be alerted to a carbon monoxide leak; it can’t be smelt, tasted or seen so it’s impossible for human senses to detect. Find out more about what you should expect from your landlord for CO safety in your home. Get protected today FireAngel recommend a CO alarm is installed between 1 m and 3 m away from each fuel‑burning appliance, as well as installing additional units in areas such as living rooms and bedrooms where you spend most time whilst at home. Activating your new FireAngel CO alarm

With our sleep easy function, you can silence low battery chirps for 8 hours, up to 10 times. This feature not only allows you to enjoy a silent night’s sleep, but gives you vital time to take action and replace your batteries. Our FA3322X4 Carbon Monoxide Alarm with digital display comes with a sealed, tamper proof battery that will last the lifetime of the alarm. The sensors within the unit will deteriorate after 10 years, so to ensure you’re protected we recommend you replace the unit after this time.Tenants, do you know your rights as a renter when it comes to CO alarms in your home? The Government announced its response to a consultation on the use of smoke and carbon monoxide alarms in domestic properties. If your FireAngel CO alarm is fully activating, and you can hear 4 loud beeps, immediately open any doors or windows in your home, stop using any appliances, switch them off and evacuate the building taking the CO alarm with you. FireAngel’s FA3322 digital carbon monoxide alarm features many icons on the LCD screen. View our guide below to help you understand what each represents. The advice below is purely provided for ‘best practice’ and should not be used independently. Please note, these alarms are not suitable for homes in Scotland under the new Fire & CO regulations.

Once your CO alarm is activated, this icon or ‘heartbeat’ will continue to flash a green LED in power mode. If a battery fault or warning has been silenced for a period of 8 hours and times out during night time, the silence period will automatically be extended once for a further 8 hours (night silence will increase the counter by 1 for sleep easy). Please note, this feature is not available with the FA3820 or FA3313 alarms. Understanding FA3322 digital display indicators https://www.fireangel.co.uk/wp-content/uploads/2022/10/MA0394R1-FireAngel-CO-Icon-Guide-Blog-Assets-Identifier-Guide-Draft-1_Power-Nightime-Sensing.mp4 However, if your CO alarm is beeping, flashing red or not responding during a test, follow our troubleshooting guide to decipher the cause. This guide applies to FireAngel FA3313 and FA3820 alarms. Why is my FireAngel CO alarm going off?

Customer Reviews

If your CO alarm is beeping once, twice or three times regularly, you may need to replace your alarm batteries, or you could be experiencing exposure to low levels of CO. The guide below will help to identify the cause of beeping.