Do NOT turn off the power during the upgrade process, as it may cause permanent damage to the product. Microsoft® Windows® 98SE, NT, 2000, XP, Vista™ or Windows 7/8/10/11, MAC® OS, NetWare®, UNIX® or Linux.

Note: Compared with the RJ45 Console cable and USB-to-RS232 cable, it might be more difficult to enter the BootUtil with a Micro-USB cable. If you still cannot enter the BootUtil after several attempts, you may get a USB-to-RS232 cable. For example, the show command can display information about many functions, you can enter the following command to view all the information that the show command can print, note that there is a space before the question mark, otherwise it is auto-completion. The switch supports configuring IGMP Snooping on a per-VLAN basis. After IGMP Snooping is enabled globally, you also need to enable IGMP Snooping and configure the corresponding parameters for the VLANs that the router ports and the member ports are in. The command is “ip igmp snooping vlan-config vlan-id”.

Firmware

In summary, to set a port as an access port for a certain VLAN, take VLAN 100 as an example, the common configuration is: With Fast Leave enabled on a VLAN, the switch will remove the (Multicast Group, Port, VLAN) entry from the multicast forwarding table before forwarding the leave message to the querier. This helps to reduce bandwidth waste since the switch no longer sends the corresponding multicast streams to the VLAN of the port as soon as the port receives a leave message from the VLAN. Please verify the hardware version of your device for the firmware version. Wrong firmware upgrade may damage your device and void the warranty. ( Normally Vx.0=Vx.6/Vx.8 (eg:V1.0=V1.6/V1.8); Vx.x0=Vx.x6/Vx.x8 (eg:V1.20=V1.26/V1.28) The querier is essential for IGMP Snooping to work properly. Usually, a router in the network can act as a querier. The switch can also act as a querier, but it is disabled by default, if you need to enable it, you can configure it as follows.

Using Omada controller to configure multiple SSIDs with different VLANs on TP-Link Omada EAPs and Switches to work with a non-Omada gateway(Multi-Net NAT supported) 07-07-2023 17569 IMPORTANT: To prevent upgrade failures, please read the following before proceeding with the upgrade process This chapter will introduce some CLI basics, including how to access the CLI, switch port types, command abbreviations, auto-completion, etc.After entering part of a command, you can press the TAB key or a question mark (?) then the switch will automatically complete the command. If your input corresponds to more than one command, the switch will not auto-complete but will display all related commands. After you finish the configurations, don't forget to save them, otherwise, they will be lost if you power off or reboot the switch. Note that TP-Link switches use Auto duplex mode by default and it is recommended to keep the mode if there are no connection problems. Using the Omada controller to configure multiple SSIDs with different VLANs on TP-Link Omada EAPs and Switches to work with a non-Omada gateway(Multi-Net NAT supported) 06-08-2023 17569

You can enable Fast Leave by enabling the feature for both the VLAN and the Port when there is only one client connected to the access port.

How to Configure Management VLAN on TP-Link Smart and Managed Switches Using the New GUI 05-18-2023 25766

Some official firmware of TP-Link products can be replaced by the third party firmware such as DD-WRT. TP-Link is not obligated to provide any maintenance or support for it, and does not guarantee the performance and stability of third party firmware. Damage to the product as a result of using third party firmware will void the product's warranty. Open Source Code For Programmers (GPL) If your computer has a serial port (COM), please connect it to the console port (RJ45) of the switch, with the RJ45 console cable. A commonly used option is “Unknown Multicast Groups”, by default, it is Forward, which means the switch forwards the multicast streams that are sent to unknown multicast groups. You can change the option to Discard so that the switch discards the multicast streams. Note to discard them, you need to enable MLD Snooping first.What's the difference between the Master Administrator, Administrator and Viewer accounts in the Omada Controller? 04-12-2023 16282 Three networks with different VLAN IDs have been registered on the router and three computers should be connected to three different networks. Now we need to configure VLAN on the switch. VLAN and port configurations are listed below: Please note: The products of TP-Link partly contain software code developed by third parties, including software code subject to the GNU General Public Licence (“GPL“), Version 1/Version 2/Version 3 or GNU Lesser General Public License ("LGPL"). You may use the respective software condition to following the GPL licence terms. What's the difference between Master Administrator, Administrator and Viewer account in Omada Controller? 04-20-2023 16282 V2: 1589.31 BTU/hr (110 V/60 Hz) (with 384 W PD connected); 117.38 BTU/hr (110 V/60 Hz) (no PD connected)